FA1761F/FA3861F USER’S GUIDE P.0
Table of contents
■General description--------------------------------------------------------------------1
■FA1761F--------------------------------------------------------------------------------------1
■FA3861F--------------------------------------------------------------------------------------1
■Common specifications--------------------------------------------------------------1
■Dimension of FA1761F----------------------------------------------------------------2
■Dimension of FA3861F----------------------------------------------------------------2
■Installation ---------------------------------------------------------------------------------2
■Illustration of front panel----------------------------------------------------------- 3
■Installation place----------------------------------------------------------------------- 4
■Installation method------------------------------------------------------------------------------- 4
■Power line and ground connections ----------------------------------------- 4
■ON/OFF output and PID control output connections----------------- 5
■Communication connections----------------------------------------------------- 5
■Initial set------------------------------------------------------------------------------------ 6
■Key functions in running------------------------------------------------------------ 6
■Over temp. display----------------------------------------------------------------------7
■Under temp. display--------------------------------------------------------------------7
■ON/OFF of key-lock---------------------------------------------------------------------7
■Auto-tuning---------------------------------------------------------------------------------7
■PID control display---------------------------------------------------------------------7FA1761F/FA3861F USER’S GUIDE P.1
| General description The FA1761F/FA3861F is a temperature- humidity controller for the dry/wet bulb system without transducer。
FA1761F Name ：Temperature controller
Model ：FA1761F（Recorder output include）
Input ：Pt100Ω
Accuracy：±0.3℃
Setting range：SCLL -99.0~0.0℃ SCLH 10.0~200.0℃ Display range：-99.9~210.0℃
FA3861F Name ：Humidity controller
Model ：FA3861F（Recorder output include）
Input ：Pt100Ω
Accuracy：±1％
Setting range：SCLL 0.0~40.0﹪ SCLH 60.0~100.0﹪
| Common specifications Display：PV 8㎜ red LED SV 8㎜ green LED （7 segments，4 character positions）
Display cycle：1 sec.
Control：PID（SSR） + ON/OFF + ON/OFF
Output ：PID output－SSR ON/OFF output－relay contact output
Action mode：reverse（low）/direct（high）
Proportional band：0.0~50.0℃/﹪
Integral time：0~99min.59 sec.
Derivative time：0~99min.59sec.
Control cycle：1~30 sec.
Hysteresis of alarm：0.1~ 2.5℃/﹪
Deviation setting：±30.0℃/﹪
Recorder output：SCLL~SCLH──DC 4~20mA
Power voltage：AC100 / 110V ±10﹪or AC200 / 220V ±10﹪ 50 / 60Hz 4VA
Memory backup：approx.10 years（at 23℃±2℃，55±10％RH，for standard model）
Dimensions：（H）96 （W）48 （D）129㎜
Panel cutout：（H）90±0.5 （W）43±0.5㎜
Weight：approx.500g Standard Accessory：mounting 2pcs/1set |
FA1761F/FA3861F USER’S GUIDE P.2
Dimension of FA1761F
Dimension of FA3861F
Installation
■1 set ■N sets
FA1761F/FA3861F USER’S GUIDE P.3
Illustration of front panel
（1） 4 character red LED：Display of PV。When we want to key-in a value，the position glittered with this value. If display＝HHHH，it means the present value（PV）is higher than 『SCLH』 ；If display＝LLLL，it means the present value（PV）is lower than 『SCLL』。
（2） 4 character green LED：Display of SV。When we want to key-in a value，the position glittered with this value.SV and percent of PID output are changeable。
（3） Display of output1：Light lamped when output1 is ON。
（4） Display of output2：Light lamped when output2 is ON。
（5） Display of output3：Light lamped when output3 is ON。
（6） Display of communication：It’ll check automatically once every second.（Communicate status between FA1761F and FA3861F），if the status is OK，it glittered with lamp。
（7） Function key：We can change the display mode by pressing this key。
（8） Left key：For input position moving。
（9） Up key：Increase value or function select。
（10） Down key：Reduce value or function select。
（11） Unit：Temperature（FA1761F）-℃；Humidity（FA3861F）-﹪。
FA1761F/FA3861F USER’S GUIDE P.4
Installation place
■Place where an ambient temperature is 0 to 40℃，and relative humidity is 80﹪RH or less。
■Place where no water splash and non-condensing develop。
■Place where no direct sunshine exist。
■Place where is clear and dust or corrosive gas are not present。
■Place where is far from noise-generating devices such as heavy duty solenoid switches and phase control SCRs。
Installation method
■Insert the FA1761F/FA3861F unit from through the cutout on the panel。
■Secure two claws of the mounting brackets to the holes on the side panel of the unit。
■Tighten the screws for the mounting brackets to secure the units。
Power line and ground connections
■The power line and ground connections are made at the FA1761F/FA3861F’s terminal board。
■The FA1761F/FA3861F is designed to operate on 100/110VAC or 200/220VAC 50/60Hz power line。
■Make sure to connect the G（ground）terminal to the earth to minimize external interference。
■For AC100V or AC110V。 ■For AC200V or AC220V。
FA1761F/FA3861F USER’S GUIDE P.5
ON/OFF output and PID control output connections
Communication connections
FA1761F/FA3861F USER’S GUIDE P.6
Initial set
This item contains setting range selection、offset adjust、action mode selection（reverse or direct）。
The initial set display is shown from the normal display by simultaneously pressing the two keys： and for a while，at the same time，PID output＝OFF。
Under this status，It will change by pressing key in sequence as below：
| Display | Name | Function |
| SCLL | Scale Low | The low limit value of setting for Temp. or Humi. |
| SCLH | Scale High | The high limit value of setting for Temp. or Humi. |
| oFFS | Offset Adjust | Range：±5.0。 Example：If deviation value＝+1，input value＝-1。 |
| cycL | Cycle Time | Range：1~30 sec.。 |
| LMTL | Limit Low | The low limit value of PID output。 Range：0~30。 |
| LMTH | Limit High | The high limit value of PID output。 Range：70~100。 |
| PID | PID Zone | The cut point of PID zone。（2 parts） |
| SEt | Set Method | AbSo(Absolute)/DeviationdEU1 selection of output2 and output3。
|
| oPEr | Operate Mode | cont(Control)/ALAr(Alarm) selection of output2 and output3。
|
| out1 | Out1 | HigH(High)/Louu(Low) selection of output1。 |
| out2 | Out2 | HigH(High)/Louu(Low) selection of output2。
（When operate mode＝Alarm，it decided automatically） |
| out3 | Out3 | HigH(High)/Louu(Low) selection of output3。
（When operate mode＝Alarm，it decided automatically） |
| uuEt | Wet | Temperature display of wet bulb。 |
| Loc | Loc | Lock function selection。 |
| tyPE | Type | Display of controller’s model。 |
Key functions in running
Green LED：It will change by pressing key in sequence as below：（In running）
→Set1→Pb L→It L→dt L→Pb H→It H→dt H→Set2→diF2→SEt3→diF3
FA1761F/FA3861F USER’S GUIDE P.7
| Display | Name | Function |
| SEt1 | Set 1 | Setting of output1 |
| Pb L | Proportional Band Low | Setting of P（Low） |
| It L | Reset Time Low | Setting of I（Low） |
| dt L | Reset Time Low | Setting of d（Low） |
| Pb H | Proportional Band High | Setting of P（High） |
| It H | Reset Time High | Setting of I（High） |
| dt H | Reset Time High | Setting of d（High） |
| SEt2 | Set 2 | Setting of output2 |
| diF2 | Differential Gap2 | Hysteresis of output2 |
| SEt3 | Set 3 | Setting of output3 |
| diF3 | Differential Gap3 | Hysteresis of output2 |
■ Setting range of P：0.0~50.0 deg / ﹪。
■ Setting range of I and D：0.00~99.59(0~99min.59sec.)
■ Setting range of differential gap：0.1~2.5 deg / ﹪。
Over temp.display
It will show the error message as below：HHHH ，at the same time，PID output＝OFF。
Under temp.display
It will show the error message as below：LLLL ，at the same time，PID output＝OFF。
ON/OFF of key-lock
We can change the key lock ON/OFF from the normal display by simultaneously pressing the two keys： and for a while。
Auto-tuning
We can change the auto-tuning ON/OFF from the normal display by simultaneously pressing the two keys： and for a while。
PID control display
We can change the setting value/percent of PID output from the normal display by simultaneously pressing the two keys： and for a while。
會員1.png)
